(Oct 11) Increase RF and Microwave Test Efficiency and Throughput
Increase RF and Microwave Test Efficiency and Throughput (Oct 11)Original air date: 10/11/2017
Sau-Peng Tang RF & Microwave Brand ManagerKeysight Technologies, Inc.
Do you need to improve the test efficiency and throughput of your RF and Microwave designs? This webcast will demonstrate how to select and configure your system with the optimal microwave test accessories to help you increase output, build a fast and accurate design validation test, improve noise figure measurements, and accelerate overall throughput resulting in a lower cost of test.
(Dec 14) Mastering Noise Figure Measurements
Mastering Noise Figure Measurements (Dec 14)Original air date: 12/14/2017
Nizar MessaoudiRF and Microwave EngineerKeysight Technologies
With the move to millimeter wave in 5G and Satellite communications, transceiver designers are faced with increasing challenges to differentiate their products. Characterizing the noise contributed by RF and microwave amplifiers and frequency converters is essential for optimizing overall system performance. Noise figure, the accepted figure-of-merit, is typically measured using the widely-understood Y-factor or hot/cold method. However, when using a vector network analyzer, the less-familiar cold-source method lends itself to advanced error-correction techniques that enable exceptional measurement accuracy. This webcast will provide an overview of both techniques and contrast their strengths and accuracy limitations.
Microwave Device Characterization Using the Latest Vector Network Analyzers
Microwave Device Characterization Using the Latest Vector Network Analyzers (On Demand)Original air date: 10/5/2017
Rosana CheruvelilNetwork Analyzer Brand SpecialistKeysight Technologies, Inc.
During this one hour webcast, we will discuss basic linear network analyzer measurements including insertion loss, return loss, gain compression and deviation from linear phase. We will then focus on additional advanced VNA capabilities including spectrum analysis and noise figure analysis.
Millimeter-wave Component Characterization
Millimeter-wave Component Characterization (On Demand)Original air date: 9/7/2017
Suren SinghIndustry Applications SpecialistKeysight Technologies
Why this webcast is important:
With the increased demand for the transfer of large volume of data at high speeds, there is an increasing need to utilize the millimeter wave frequency band . This places an increased demand on designers and manufacturers in the industry to fully characterize and test both active and passive components at the millimeter wave frequencies. This webcast will focus on how a Vector Network Analyzer can be utilized to address the need for millimeter wave component characterization for both passive and active devices.
Understanding RF and Microwave Analysis Basics
Understanding RF and Microwave Analysis Basics (On Demand)Original air date: 9/13/2017
Kimberly Cassacia Product Line Brand Manager Keysight Technologies, Inc.
With increasingly complex design and measurement challenges and rapidly changing technology, engineers must have a strong foundation in basic measurement and simulation techniques in RF analysis. This session will discuss key fundamentals needed to optimize the analysis of RF signals. Different types of basic measurements and the use of a spectrum analyzer and signal generator will be covered.
Understanding Phase Noise and Why it Matters
Understanding Phase Noise and Why it Matters (On Demand)Original air date: 7/12/2017
Riadh SaidPlatform Planning Engineer, High Frequency Measurements Center of ExcellenceKeysight Technologies
Why this webcast is important:
Engineers developing cutting edge radar and communications systems know that phase noise is a characteristic that can limit system performance. In radar systems, phase noise degrades the ability to process Doppler information. In digitally modulated communication systems, phase noise degrades error vector magnitude.
This webcast explains fundamental phase noise characteristics and tradeoffs including cost, switching speed and optimization of wide vs. narrow offsets in order to optimize performance. It also discusses related signal generation techniques such as frequency references, frequency converters, and frequency synthesis and their respective roles in transmitter and receiver test.
Who should attend:
Engineers developing RADAR, EW, Satellite, or digitally modulated communication system receivers and transmitters.
Verifying RF Short Range Communication in IoT
Verifying RF Short Range Communication in IoT (On Demand)Original air date: 6/27/2017
Jake Daly SA Product Brand Specialist Keysight Technologies, Inc.
IoT involves wireless networks that must accurately and instantaneously communicate to each other and to the cloud. Verifying the signal robustness of these radio links is key in ensuring a design’s integrity. This webcast will cover measurement and test methods of short-range communications including Bluetooth, Zigbee, Z-wave, and Sub-GHz. RF test solutions that meet a variety of application needs ranging from automotive, home automation to healthcare will be demonstrated.
EMI Interference Analysis and Troubleshooting
EMI Interference Analysis and Troubleshooting (On Demand)Original air date: 6/14/2017
Chris Harrell Application Engineer Keysight Technologies, Inc.
Signal analyzers are used to characterize RF signals, including EMI interference analysis and diagnostics. A full EMI compliance test can be expensive and time-consuming. So why not use the spectrum analyzer on your bench to evaluate the EMI risk of your product, before going to the test house? This webcast will cover EMI basics, EMI interference, and EMI characterization and test using the Keysight X-series signal analyzers.
Wireless LAN Evolution
Wireless LAN Evolution (On Demand)Original air date: 5/9/2017
Kimberly Cassacia Product Line Brand Manager Keysight Technologies, Inc.
With the demand for new usage models and more applications, dense Wi-Fi deployments and more outdoor and public access, extensive effort and work are in progress in IEEE on emerging standards, from 802.11ac to 802.11ax or from 802.11ad to 802.11ay. This webcast will discuss the evolution of WLAN technologies along with solutions addressing associated test challenges such as high order modulation, OFDMA and MIMO.
Who should attend:
Wireless system, subsystem and component design and test engineers and engineering managers interested in learning techniques for keeping up with latest standards pushing the limits of device bandwidth, adjacent channel and spurious performance, and complexity.
5G Beams and Dreams: From FD-MIMO to Massive MIMO
5G Beams and Dreams: From FD-MIMO to Massive MIMO (On Demand)Original air date: 4/27/2017
Will SitchMIMO Program Director and Worldwide Business Development ManagerKeysight Technologies
What is the webcast about:
Join Keysight’s webcast to get a feel for the pulse of the 5G MIMO marketplace and learn solutions for difficult MIMO questions. What is the difference between beamsteering and beamforming? What is Full Dimension MIMO, and how is it different from regular MIMO? Will Massive MIMO be needed at millimeter-wave frequencies? Will 5G MIMO mean I need a new phone? How will MIMO improve quality of service for end-users?
Who should attend:
Advanced development researchers, design engineers, validation engineers, test engineers, architects, project managers, program managers, application managers, and application engineers.
RF Fundamentals Part 4: RF and Microwave Power Measurements
RF Fundamentals Part 4: RF and Microwave Power Measurements (On Demand)Original air date: 4/18/2017
Eric Breakenridge Aerospace/Defense/Government Solutions Manager Keysight Technologies, Inc.
Power measurements are fundamental to RF & microwave industries, but is the standalone power meter still relevant among the plethora of advanced instruments available today? During this one hour webcast, we will discuss standalone power measurement instruments, how they work, why they are important and where they fit within the RF test bench. We will describe the technologies and topologies applied to power measurements and explore how best to take advantage of the capabilities offered. Factors effecting accuracy and traceability will be presented along with detailed application examples.
Testing Microwave Backhaul Radio Systems
Testing Microwave Backhaul Radio Systems (On Demand)Original air date: 3/29/2017
Rolland Zhang Senior Product ManagerKeysight Technologies, Inc.
Microwave radio provides the quickest and the most cost effective way to backhaul broadband radio access. In order to keep the microwave radio running at its peak performance, it is crucial to install its network elements properly, test each of them to make sure they meet design specifications before turning on the system; and site radio elements need to be tested during operation to assure network service quality.
NB-IoT: A Cellular Technology Connecting the Internet of Things
NB-IoT: A Cellular Technology Connecting the Internet of Things (On Demand)Original air date: 3/22/2017
Manuel Blanco Solutions Planning Engineer Keysight Technologies, Inc.
While the LPWA( Low Power Wide Area) market has existed for some time, current implementations are fragmented and soft-standardized, leading to weaknesses in security and reliability, and very high operational costs due to incompatibility with existing infrastructure.
Narrowband-IoT (NB-IoT) is a new cellular Radio Access Technology defined by the 3GPP aimed to address this market and overcome these challenges, presented as an upgrade path to existing cellular networks. How does NB-IoT work and what are the test challenges?
This webcast will help engineers have insight into the motivational reasons, industry drivers and technical fundamentals of NB-IoT.
Millimeter-wave Challenges (On Demand)Original air date: 2/23/2017
Pete CainMillimeter-wave Solution Planner Keysight Technologies
While the frequency of “mmWave” systems can vary from 10-100 GHz, there are aspects of system design and the impact of hardware limitations that are common. A combination of high frequency and wide bandwidth require close attention to broadband noise, phase noise, linearity, frequency response and power dissipation. The use of directional antennas introduces another dimension to the problem of maintaining an effective link, since beam steering is required. This webcast discusses these issues and some solutions using a number of examples from 802.11ad and OFDM signals
RF Fundamentals Part 3 - Signal Generation, Modulation and Vector Signal Analysis
RF Fundamentals Part 3 - Signal Generation, Modulation and Vector Signal Analysis (On Demand)Original air date: 1/18/2017
Kimberly Cassacia Product Line Brand ManagerKeysight Technologies
In Part 3 of RF Fundamentals, we will focus on the challenges related to the need to generate and demodulate analog and digitally modulated signals in the RF signal chain. We’ll review CW signal generation and characteristics, including phase-noise and signal synthesis using VCOs and phase-locked-loops. You will learn about analog and digital modulation generation and measurement techniques.
IoT: LoRa® Technology Introduction and Solution Testing
IoT: LoRa® Technology Introduction and Solution Testing (On Demand)Original air date: 1/27/2017
Vivek MohanDirector of Marketing for Wireless Connectivity ProductsSemtech
Ian ReadingIndustry Segment PlannerKeysight Technologies, Inc.
Kevin Ashton coined the phrase “The Internet of Things” in 1999 when discussing applications for RFID tags. From the simple tracking and counting of RFID objects, the Internet of Things has taken off with Machine-to-Machine (M2M), Big Data and Machine Learning, enabling applications such as the smart building, smart grid and intelligent transport systems. LoRaWAN™ is a Low Power Wide Area Network (LPWAN) specification intended for wireless battery operated Things in regional, national or global networks. LoRaWAN targets key IoT requirements such as secure bi-directional communication, mobility and localization. LoRa is well accepted for its long range, excellent sensitivity, battery life, and low cost. In this webcast, we invite Semtech, the key chipset supplier and driver of LoRaWAN, to introduce their understanding of this market. Keysight, as a leading Test & Measurement company will introduce LoRa Transmitter, Receiver and power consumption test methods.
RF Fundamentals Part 2 - Spectral Analysis
RF Fundamentals Part 2 - Spectral Analysis (On Demand)Original air date: 12/8/2016
Kevin Nguyen RF & Microwave Applications EngineerKeysight Technologies
In Part 2 of RF Fundamentals, we will continue our discussion of measurement challenges associated with the RF signal chain. We will discuss swept tuned and FFT receiver techniques and optimization of spectral search techniques, including RBW, VBW and dynamic range criteria for the most accurate measurements. You will also learn about distortion and noise contributions.
Improve the Efficiency of Analyzing RF / MW Interference with RTSA
Improve the Efficiency of Analyzing RF / MW Interference with RTSA (On Demand)Original air date: 11/29/2016
Rolland Zhang Senior Product ManagerKeysight Technologies
A/D communication systems are moving to higher frequency, deploying much narrower RADAR pulses and implementing highly encrypted digital wireless systems for communication. In order to detect and troubleshoot these challenging signals, real-time signal analysis (RTSA) capability is needed for field test. We will explore RADAR, EW and interference issues utilizing the RTSA technology of Keysight’s FieldFox RF/MW analyzers.
RF Fundamentals Part 1: The RF Signal Chain and Network Analysis
RF Fundamentals Part 1: The RF Signal Chain and Network Analysis (On-Demand)Original air date: 11/10/2016
Riadh Said Platform Planning EngineerComponent Analysis Center of ExcellenceKeysight Technologies, Inc.
During this 1-hour webcast, you will learn about the RF transmit/receive signal chain*. We will review the role of network analysis in characterizing the key components of these systems, covering transmission line theory, S-parameters, Smith Charts, impedance measurements/matching and calibration and error correction. You will learn about transmit/receive and directivity paths and how to optimize dynamic range and accuracy.
*In RF/Microwave communications systems, data is transmitted using modulation, up-conversion and amplification and is detected or received through amplification, down-conversion and demodulation. We will refer to this as the RF signal chain.
Generating Wideband, Multi-Channel RADAR Signals Using High-Speed AWGs
Generating Wideband, Multi-Channel RADAR Signals Using High-Speed AWGs (On-Demand)Original air date: 11/3/2016
Thomas DipponStrategic Product PlannerKeysight Technologies, Inc.
This presentation was developed to give an overview of why you should consider using a high-speed arbitrary waveform generator (AWG) not just for I/Q baseband generation, but for direct RF signal generation – in particular, for pulsed RADAR applications. After looking at the basic high-speed AWG architecture, you’ll understand the capabilities and limitations of using an AWG relative to a traditional signal generator. Finally, we’ll look at a number of example measurements that will show some of the unique benefits of using an AWG in this application.
Street Address Line 1*
Street Address Line 2
State/Province*Please Select…Outside the US or CanadaAlaskaAlabamaArkansasAmerican SamoaArizonaCaliforniaColoradoConnecticutD.C.DelawareFloridaMicronesiaGeorgiaGuamHawaiiIowaIdahoIllinoisIndianaKansasKentuckyLouisianaMassachusettsMarylandMaineMarshall IslandsMichiganMinnesotaMissouriMarianasMississippiMontanaNorth CarolinaNorth DakotaNebraskaNew HampshireNew JerseyNew MexicoNevadaNew YorkOhioOklahomaOregonPennsylvaniaPuerto RicoPalauRhode IslandSouth CarolinaSouth DakotaTennesseeTexasUtahVirginiaVirgin IslandsVermontWashingtonWisconsinWest VirginiaWyomingMilitary AmericasMilitary Europe/ME/CanadaMilitary PacificAlbertaManitobaBritish ColumbiaNew BrunswickNewfoundland and LabradorNova ScotiaNorthwest TerritoriesNunavutOntarioPrince Edward IslandQuebecSaskatchewanYukon Territory
Country*Please selectUnited StatesUnited KingdomCanadaIndiaNetherlandsAustraliaSouth AfricaFranceGermanySingaporeSwedenBrazil--------------AfghanistanÅland IslandsAlbaniaAlgeriaAmerican SamoaAndorraAngolaAnguillaAntarcticaAntigua and BarbudaArgentinaArmeniaArubaAustraliaAustriaAzerbaijanBahamasBahrainBangladeshBarbadosBelarusBelgiumBelizeBeninBermudaBhutanBoliviaBosnia and HerzegovinaBotswanaBouvet IslandBrazilBrit/Indian Ocean Terr.Brunei DarussalamBulgariaBurkina FasoBurundiCambodiaCameroonCanadaCape VerdeCayman IslandsCentral African RepublicChadChileChinaChristmas IslandCocos (Keeling) IslandsColombiaComorosCongoCongo, The Dem. Republic OfCook IslandsCosta RicaCôte D'IvoreCroatiaCubaCyprusCzech RepublicDenmarkDjiboutiDominicaDominican RepublicEcuadorEgyptEl SalvadorEquatorial GuineaEritreaEstoniaEthiopiaFalkland IslandsFaroe IslandsFijiFinlandFranceFrench GuianaFrench PolynesiaFrench Southern Terr.GabonGambiaGeorgiaGermanyGhanaGibraltarUnited KingdomGreeceGreenlandGrenadaGuadeloupeGuamGuatemalaGuineaGuinea-BissauGuyanaHaitiHeard/McDonald Isls.HondurasHong KongHungaryIcelandIndiaIndonesiaIranIraqIrelandIsraelItalyJamaicaJapanJordanKazakhstanKenyaKiribatiKorea (North)Korea (South)KuwaitKyrgyzstanLaosLatviaLebanonLesothoLiberiaLibyaLiechtensteinLithuaniaLuxembourgMacauMacedoniaMadagascarMalawiMalaysiaMaldivesMaliMaltaMarshall IslandsMartiniqueMauritaniaMauritiusMayotteMexicoMicronesiaMoldovaMonacoMongoliaMontserratMoroccoMozambiqueMyanmarN. Mariana Isls.NamibiaNauruNepalNetherlandsNetherlands AntillesNew CaledoniaNew ZealandNicaraguaNigerNigeriaNiueNorfolk IslandNorwayOmanPakistanPalauPalestinian Territory, OccupiedPanamaPapua New GuineaParaguayPeruPhilippinesPitcairnPolandPortugalPuerto RicoQatarReunionRomaniaRussian FederationRwandaSaint Kitts and NevisSaint LuciaSamoaSan MarinoSao Tome/PrincipeSaudi ArabiaSenegalSerbia and MontenegroSeychellesSierra LeoneSingaporeSlovak RepublicSloveniaSolomon IslandsSomaliaSouth AfricaSpainSri LankaSt. HelenaSt. Pierre and MiquelonSt. Vincent and GrenadinesSudanSurinameSvalbard/Jan Mayen Isls.SwazilandSwedenSwitzerlandSyriaTaiwanTajikistanTanzaniaThailandTimor-LesteTogoTokelauTongaTrinidad and TobagoTunisiaTurkeyTurkmenistanTurks/Caicos Isls.TuvaluUgandaUkraineUnited Arab EmiratesUnited StatesUS Minor Outlying Is.UruguayUzbekistanVanuatuVatican CityVenezuelaViet NamVirgin Islands (British)Virgin Islands (U.S.)Wallis/Futuna Isls.Western SaharaYemenZambiaZimbabwe
Subscribe to Electronic Design Today
Up to date coverage of the Electronics Industry
This eNewsletter is delivered five days a week
Why are you viewing this broadcast today?*
Please select one
A purchase need
To learn more about the solution that I’ve already purchased
To learn more about the solution but no purchase planned